Thing #1…How to properly apply borders to a quilt…

Blog - 8 Things Theme Photo

 

I don’t know about you, but when I’m working on a project…especially a large, time intensive one, sometimes I get so excited to get it done that I hurry up to get to the end.  Sometimes this means working on it more frequently, and sometimes it means not taking enough time to do things RIGHT.  

Unfortunately, when it comes to quilt-making, that last step before sending your top to the quilter can have a huge effect on how your quilt turns out!  Rushing through it, or simply not knowing the best method can cause all sorts of problems.  Wavy borders are a long-armer’s most dreaded adversary.  I want so much to enhance a quilt with stitching, and sometimes when there is excess fabric in the borders, the quilting seems to highlight the problem, making it seem even worse!  I try to notice this problem when I am measuring a quilt, but sometimes it isn’t obvious until the quilt gets on the machine…often times I will call a client whose borders are a tad out of shape, and she will say something like “just quilt it anyway”.  Sometimes the quilting does help to take up some of the fullness, but other times I have no choice but to create a few tucks, and drive over them.

DSCN2194 (2)
Wavy borders could be improved, or avoided altogether if a few steps were taken as the borders were applied.  I have to admit, I didn’t make this method up myself.  It has been gleaned from several quilting books, and patterns.  Many patterns leave out the step by step process, so I will share the process I use with you.

Step #1  Square up your quilt.  Like squaring up blocks, squaring the top is an often overlooked, but valuable step.  It’s pretty simple, especially if you are relatively accurate when piecing.  Just fold your quilt in half, and in half again.  Using a large square ruler, trim the corners so they are nice and square:

006

 

 

Step #2:  Before you unfold your quilt all the way, take the measurement across the quilt at the halfway point.  With your quilt folded in half, use your cutting mat to measure the width of your quilt at the fold.  I have heard some teachers say to measure it at several points and take the average of these, but as I said before…when I’m almost done…I get a little too hasty to spend too much time on one task.  This one measurement has always worked well for me, but if you’d like to try multiple measurements and take the average, be my guest.  Make sure you write down this measurement!
007 (2)

 

Step #3:  The measurement you took in step #2 is a good representation of what your quilt width should be.  That is what the edges would be without any error, or stretching of bias.  This is the length you should cut your borders for the top and bottom of your quilt.  If my border strips aren’t long enough, I usually piece them together using a diagonal seam.

 

2015-02-20 10.44.41
(sorry about the wrinkles!)

Step #4:  This is the key to wavy border prevention.  At this point you have a quilt top and borders that are “made for each other” although the edges of your quilt may not be an exact fit.  The trick is, to ease any fullness you may have and spread that fullness across the width of your quilt.  In order to do this you need to match up the borders and sides at corresponding intervals. Take each piece (border and top of quilt) and fold it twice.  Each fold will represent 1/4 of the width of your quilt.  Either press or pin to mark your top and border. They are not easy to see, but the border strip in the following photo has 3 pins, one at the center, and one at each halfway point between the center and the end.  Make sure to place corresponding pins on the top and bottom of your quilt as well as each of the border pieces.

 

012

 

Step #5:  We’re getting closer!  Next, lay out the border strip on top of the quilt (right sides together) and pin these pieces together, matching the center and 1/4 points that are pinned.  Once those points are pinned, you may add a few pins between them being sure to evenly distribute any fullness you may have.

 

DSC01278

 

Step #6:  Time to sew on the borders!   Using a 1/4″ seam, and keeping your border on top, sew the border onto the body of the quilt.  If there is any fullness, either on the border or the quilt top be sure to ease it between the pins.  One way to do this is by holding the layers taught as you sew which stretches the shorter item a bit, you may also use a stiletto for equally distributing the fabric.

 

2015-02-26 17.55.35

The source of wavy borders is then caught in this seam, and  your quilt should turn out square and relatively flat.  Once both top and bottom borders are sewn on, it’s time to press.

Step #7:  I usually press so that the seam is toward the border fabric.  I don’t think it really matters much, but since I was always taught to press on the top of the piece, this works out better for me.    Lay the quilt on your pressing surface, border side up, and use tip of your iron to get into the seam and press it flat…pushing away from you.

 

2015-02-26 18.00.29

 

Step #8:  Now that you have applied the top and bottom borders, you can repeat the process from step #2, including your new borders in your measurement for the side borders.  Your quilt is now ready to be basted and quilted…or sent to your favorite professional long-arm quilt artist!

 

Please keep in mind, that accuracy when piecing will also go a long way toward contributing to a flat quilt without tucks or waves.  No quilt is perfect, but if your quilt top has a great deal of fullness due to inaccurate piecing, sewing the borders on correctly will not fix the problem. Due to bias pieces on the edge, or the piecing process, edges of quilt tops are frequently longer than the body of the quilt should be.  This method is meant to ease that discrepancy.

I hope this last tip was helpful.  What about you, do you have any tips you’d like to share?